IPL g5da0ceb
D-1e
HW Reset
miupll_233MHz
MIU0 zq=0x003b
miu_bw_set
utmi_1_init done
utmi_2_init done
utmi_3_init done
usbpll init done......
cpupll init done
SPI 54M
clk_init done
P1 USB_rterm trim=0x0000
P1 USB_HS_TX_CURRENT trim=0x0001
P2 USB_rterm trim=0x0000
P2 USB_HS_TX_CURRENT trim=0x0001
P3 USB_rterm trim=0x0000
P3 USB_HS_TX_CURRENT trim=0x0001
PM_vol_bgap trim=0x0002
GCR_SAR_DATA trim=0x0192
ETH 10T output swing trim=0x0000
ETH 100T output swing trim=0x0000
ETH RX input impedance trim=0x0000
ETH TX output impedance trim=0x0001
MIPI_HS_RTERM trim=0x0001
MIPI_LP_RTERM trim=0x0000
128MB
BIST0_0001-OK
Enable MMU and CACHE
Load IPL_CUST from SPINAND
QUAD MODE ENABLE
Checksum OK
IPL_CUST g5da0ceb
runUBOOT()
runUBOOT()
[SPINAND]
SPI 54M
Load UBOOT from SPINAND
-Verify UBOOT CRC32 passed!
-Decompress UBOOT XZ
decomp_size=0x0009bbf4
Disable MMU and D-cache before jump to UBOOT
U-Boot 2015.01 (Feb 02 2021 - 18:33:26)
Version: I2g1ad5d0c
Watchdog enabled
DRAM:
WARNING: Caches not enabled
SPINAND: _MDrv_SPINAND_GET_INFO: Found SPINAND INFO
(0xCD) (0xEB) (0x11)
SPINAND: board_nand_init: CIS contains part info
256 MiB
In: serial
Out: serial
Err: serial
gpio debug MHal_GPIO_Pad_Set: pin=4
gpio[4] is 1
gpio debug MHal_GPIO_Pad_Set: pin=18
gpio[18] is 1
NAND read: device 0 offset 0x4c0000, size 0x60000
Time:85802 us, speed:4582 KB/s
393216 bytes read: OK
gpio debug MHal_GPIO_Pad_Set: pin=71
gpio[71] is 0
UBI: parsing mtd_dev string 'mtd=10'
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI: attached mtd1 (name "mtd=10", size 48 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 3, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2052046083
UBI: available PEBs: 0, total reserved PEBs: 384, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 22000000
No size specified -> Using max size (2031616)
gpio debug MHal_GPIO_Pad_Set: pin=71
gpio[71] is 1
## Booting kernel from Legacy Image at 22000000 ...
Image Name: MVX4##I2M#g1ad5d0cKL_LX409##[BR:
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 1965708 Bytes = 1.9 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Uncompressing Kernel Image ...
[XZ] !!!reserved 0x21000000 length=0x 1000000 for xz!!
XZ: uncompressed size=0x3e4000, ret=7
OK
atags:0x20000000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.84 (sk@ubuntu) (gcc version 8.2.1 20180802 (GNU Toolchain for the A-profile 1
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] early_atags_to_fdt() success
[ 0.000000] OF: fdt:Machine model: INFINITY2M SSC011A-S01A-S
[ 0.000000] LXmem is 0x7f00000 PHYS_OFFSET is 0x20000000
[ 0.000000] Add mem start 0x20000000 size 0x7f00000!!!!
[ 0.000000]
[ 0.000000] LX_MEM = 0x20000000, 0x7f00000
[ 0.000000] LX_MEM2 = 0x0, 0x0
[ 0.000000] LX_MEM3 = 0x0, 0x0
[ 0.000000] EMAC_LEN= 0x0
[ 0.000000] DRAM_LEN= 0x0
[ 0.000000] deal_with_reserved_mmap memblock_reserve success mmap_reserved_config[0].reserved_start=
[ 0.000000] 0x27c00000
[ 0.000000]
[ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[0].reserved_start=
[ 0.000000] 0x26700000
[ 0.000000]
[ 0.000000] cma: Reserved 2 MiB at 0x26400000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 13 pages/cpu @c66bf000 s21016 r8192 d24040 u53248
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 26882
[ 0.000000] Kernel command line: wt_board=WT2022 console=ttyS0,115200 rootfstype=squashfs,ubifs rootwait=1)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 98060K/108544K available (2433K kernel code, 200K rwdata, 1060K rodata, 160K init, 147)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8000000 - 0xff800000 ( 888 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc7f00000 ( 127 MB)
[ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB)
[ 0.000000] .text : 0xc0008000 - 0xc02689e8 (2435 kB)
[ 0.000000] .init : 0xc0390000 - 0xc03b8000 ( 160 kB)
[ 0.000000] .data : 0xc03b8000 - 0xc03ea148 ( 201 kB)
[ 0.000000] .bss : 0xc03ec000 - 0xc0410efc ( 148 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ms_init_main_intc: np->name=ms_main_intc, parent=gic
[ 0.000000] ms_init_pm_intc: np->name=ms_pm_intc, parent=ms_main_intc
[ 0.000000] ss_init_gpi_intc: np->name=ms_gpi_intc, parent=ms_main_intc
[ 0.000000] Find CLK_cpupll_clk, hook ms_cpuclk_ops
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 6.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 44s
[ 0.000005] sched_clock: 56 bits at 6MHz, resolution 166ns, wraps every 4398046511055ns
[ 0.000017] Switching to timer-based delay loop, resolution 166ns
[ 0.000347] Console: colour dummy device 80x30
[ 0.353592] console [ttyS0] enabled
[ 0.357081] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.00 BogoMIPS (lpj)
[ 0.367344] pid_max: default: 4096 minimum: 301
[ 0.371938] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.378498] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.386066] CPU: Testing write buffer coherency: ok
[ 0.390991] CPU0: update cpu_capacity 1024
[ 0.394928] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.400780] Setting up static identity map for 0x20008240 - 0x20008270
[ 0.610920] CPU1: update cpu_capacity 1024
[ 0.610926] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.611033] Brought up 2 CPUs
[ 0.623598] SMP: Total of 2 processors activated (24.00 BogoMIPS).
[ 0.629764] CPU: All CPU(s) started in SVC mode.
[ 0.634968] devtmpfs: initialized
[ 0.651689] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.659490] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 s
[ 0.669222] futex hash table entries: 16 (order: -2, 1024 bytes)
[ 0.675867] NET: Registered protocol family 16
[ 0.680703] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.689243]
[ 0.689243]
[ 0.689243] Version : MVX4##I2M#g1ad5d0cKL_LX409##[BR:master]#XVM
[ 0.689243]
[ 0.704951] GPIO: probe end[ 0.707883] [ss_gpi_intc_domain_alloc] hw:42 -> v:44
[ 0.716159] [Padmux]reset Pad_47(reg 0x101e03; mask0x70) to GPIO(org: UART0_MODE_1)
[ 0.724026] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.731878] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.748311] clocksource: Switched to clocksource arch_sys_counter
[ 0.765175] NET: Registered protocol family 2
[ 0.769998] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.776820] TCP bind hash table entries: 1024 (order: 2, 20480 bytes)
[ 0.783326] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.789673] UDP hash table entries: 128 (order: 0, 6144 bytes)
[ 0.795442] UDP-Lite hash table entries: 128 (order: 0, 6144 bytes)
[ 0.801917] NET: Registered protocol family 1
[ 0.806385] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.816405] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.831236] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.839999] io scheduler noop registered
[ 0.843764] io scheduler deadline registered (default)
[ 0.850536] i2c /dev entries driver
[ 0.854428] 1f221000.uart0: ttyS0 at MMIO 0x0 (irq = 30, base_baud = 10800000) is a unknown
[ 0.863019] 1f221200.uart1: ttyS1 at MMIO 0x0 (irq = 31, base_baud = 10800000) is a unknown
[ 0.871678] 1f220400.uart2: ttyS2 at MMIO 0x0 (irq = 32, base_baud = 10800000) is a unknown
[ 0.880280] 1f221400.uart2: ttyS3 at MMIO 0x0 (irq = 33, base_baud = 10800000) is a unknown
[ 0.889360] [Core Voltage] check_voltage_valid: Not support 0mV, use 900mV
[ 0.896491] ms_rtcpwc 1f006800.rtcpwc: rtc core: registered 1f006800.rtcpwc as rtc0
[ 0.905562] [ms_cpufreq_init] Current clk=1005326304
[ 0.911299] mstar_spinand_probe: mstar_spinand enableClock
[ 0.916633] MSYS: DMEM request: [BDMA]:0x00000840
[ 0.921441] MSYS: DMEM request: [BDMA]:0x00000840 success, CPU phy:@0x26442000, virt:@0xC6442000
[ 0.930473] MDrv_SPINAND_Init: Detected ID: MID =cd, DID =eb
[ 0.935973] _dumpNandInformation:warning, Bytes / Page : 2048
[ 0.941835] _dumpNandInformation:warning, Pages / Block: 64
[ 0.947461] _dumpNandInformation:warning, Sector/ Page : 512
[ 0.953216] _dumpNandInformation:warning, Spare / Page : 64
[ 0.958887] _dumpNandInformation:warning, Current config r:4 w:4 drv:1
[ 0.965610] mstar_spinand_probe: Magic memcmp pass
[ 0.970249] mstar_spinand_probe: Get partition (Block 0 : page 1)
[ 0.976546] mstar_spinand_probe: CIS contains part info
[ 0.981632] mstar_spinand_probe: Before nand_scan()...
[ 0.986786] 13 cmdlinepart partitions found on MTD device nand0
[ 0.992675] mstar_spinand_probe: Mtd parts parse
[ 0.997276] Creating 13 MTD partitions on "nand0":
[ 1.002098] 0x000000140000-0x0000001a0000 : "IPL0"
[ 1.009705] 0x0000001a0000-0x000000200000 : "IPL1"
[ 1.017014] 0x000000200000-0x000000260000 : "IPL_CUST0"
[ 1.024740] 0x000000260000-0x0000002c0000 : "IPL_CUST1"
[ 1.032575] 0x0000002c0000-0x000000380000 : "UBOOT0"
[ 1.040758] 0x000000380000-0x000000440000 : "UBOOT1"
[ 1.048956] 0x000000440000-0x0000004a0000 : "ENV0"
[ 1.056298] 0x0000004a0000-0x0000004c0000 : "KEY_CUST"
[ 1.063617] 0x0000004c0000-0x000000520000 : "LOGO"
[ 1.070799] 0x000000520000-0x000000580000 : "wtinfo"
[ 1.085320] 0x000000580000-0x000003580000 : "ubi"
[ 1.189752] 0x000003580000-0x000006580000 : "ubi2"
[ 1.284978] 0x000006580000-0x000010000000 : "opt"
[ 1.576463] NET: Registered protocol family 17
[ 1.581380] ThumbEE CPU extension supported.
[ 1.585498] Registering SWP/SWPB emulation handler
[ 1.591389] UBI: auto-attach mtd10
[ 1.594637] ubi0: attaching mtd10
[ 1.851527] ubi0: scanning is finished
[ 1.861830] ubi0: attached mtd10 (name "ubi", size 48 MiB)
[ 1.867163] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.874059] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.880839] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.887789] ubi0: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
[ 1.893804] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.901031] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2052046083
[ 1.910166] ubi0: available PEBs: 0, total reserved PEBs: 384, PEBs reserved for bad PEB handling: 40
[ 1.919409] ubi0: background thread "ubi_bgt0d" started, PID 460
[ 1.926250] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.931602] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.974612] ms_rtcpwc 1f006800.rtcpwc: setting system clock to 1970-01-01 00:23:46 UTC (1426)
[ 1.983170] OF: fdt:not creating '/sys/firmware/fdt': CRC check failed
[ 1.993330] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.001953] devtmpfs: mounted
[ 2.004782] This architecture does not have kernel memory protection.
[ 2.324188] init: Console is alive
[ 2.327585] init: - watchdog -
[ 2.605678] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.616086] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.638522] init: - preinit -
[ 2.700143] mount_root: loading kmods from internal overlay
[ 2.716900] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 2.723947] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 2.847524] random: procd: uninitialized urandom read (4 bytes read)
[ 2.854379] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 484
[ 2.883757] UBIFS (ubi0:2): recovery needed
[ 2.943689] UBIFS (ubi0:2): recovery completed
[ 2.948040] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 2.955832] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bys
[ 2.965786] UBIFS (ubi0:2): FS size: 25522176 bytes (24 MiB, 201 LEBs), journal size 1269760 bytes (1 MiB,)
[ 2.976192] UBIFS (ubi0:2): reserved for root: 1205474 bytes (1177 KiB)
[ 2.982808] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 5067D53C-5791-41DB-993A-22C7B2C7F9l
[ 2.995011] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 3.005358] block: extroot: not configured
[ 3.058453] UBIFS (ubi0:2): un-mount UBI device 0
[ 3.063017] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 3.072604] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 487
[ 3.147061] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 3.154771] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bys
[ 3.164681] UBIFS (ubi0:2): FS size: 25522176 bytes (24 MiB, 201 LEBs), journal size 1269760 bytes (1 MiB,)
[ 3.175158] UBIFS (ubi0:2): reserved for root: 1205474 bytes (1177 KiB)
[ 3.181741] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 5067D53C-5791-41DB-993A-22C7B2C7F9l
[ 3.301717] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 3.311646] block: extroot: not configured
[ 3.350012] mount_root: switching to ubifs overlay
[ 3.372419] procd: - early -
[ 3.375220] procd: - watchdog -
[ 4.068506] procd: - watchdog -
[ 4.071680] procd: - ubus -
[ 4.092461] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.136209] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.142687] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.148927] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.155356] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.161627] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.168036] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.174408] random: ubusd: uninitialized urandom read (4 bytes read)
[ 4.180918] procd: - init -
Please press Enter to activate this console.
[ 4.324351] [ss_gpi_intc_domain_alloc] hw:58 -> v:56
[ 4.326398] mhal: loading out-of-tree module taints kernel.
[ 4.326412] mhal: module license 'PROPRIETARY' taints kernel.
[ 4.326415] Disabling lock debugging due to kernel taint
[ 4.332456] mhal driver init
[ 4.350406] jpe driver probed
[ 4.353845] DivpProcInit 515
[ 4.378477] module [sys] init
[ 4.381531] MI_SYSCFG_SetupMmapLoader default_config_path:/config/config_tool, argv1:/config/load_mmap,argi
[ 4.402856] Function = init_glob_miu_kranges, Line = 604, Insert KProtect for LX @ MIU: 0
[ 4.411700] Function = init_glob_miu_kranges, Line = 613, [INIT] for LX0 kprotect: from 0x20000000 to 0x270
[ 4.424118] config...... strPath:/config/config_tool, argv0:/config/load_config
[ 4.434060] function:parese_Cmdline,pCmd_Section:0x7f00000
[ 4.439446] m[ 4.440784] m
a[ 4.442437] _
h[ 4.444090] e
a[ 4.445744] p
_[ 4.447398] n
a[ 4.449052] m
e[ 4.450705] 0
[ 4.452275] miu=0,sz=1500000 reserved_start=26700000
[ 4.457732] r_front->miuBlockIndex:0,r_front->start_cpu_bus_pa:0x20000000,r_front->start_cpu_bus_pa+r_fron0
[ 4.469114] r_back->miuBlockIndex:1,r_back->start_cpu_bus_pa:0x27c00000,r_back->start_cpu_bus_pa+r_back->l0
[ 4.481584] Goodix-TS 1-005d: ID 911, version: 1060
[ 4.481816] Goodix-TS 1-005d: Direct firmware load for goodix_911_cfg.bin failed with error -2
[ 4.499273] input: Goodix Capacitive TouchScreen as /devices/soc0/soc/1f223200.i2c1/i2c-1/1-005d/input/inp0
[ 4.512194] mi_sys_mma_allocator_create success, heap_base_addr=26700000 length=1500000
[ 4.520410] Kernel CONFIG_HZ = 100
[ 4.524457] Sigmastar Module version: project_commit.c8104f6 sdk_commit.677940d /home/xinhua.ye/alkaid_mp/.
[ 4.546759] module [gfx] init
[ 4.559224] module [divp] init
[ 4.576889] module [vdec] init
[ 4.593568] module [ao] init
[ 4.606985] module [disp] init
[ 4.621755] module [ai] init
[ 4.638293] module [panel] init
[ 4.663384] [ss_gpi_intc_domain_alloc] hw:59 -> v:57
[ 4.669778] reg=0x1F003410 clk=12000000, period=0x4af
[ 4.674686] reg=0x1F003408 clk=12000000, u32Duty=0x0
[ 4.680408] reg=0x1F003410 clk=12000000, period=0x4af
[ 4.686108] reg=0x1F003408 clk=12000000, u32Duty=0x4af
[ 4.697588] client [813] connected, module:sys
[ 4.701213] kmodloader: loading kernel modules from /etc/modules.d/*
[ 4.711549] usbcore: registered new interface driver usbfs
[ 4.711667] usbcore: registered new interface driver hub
[ 4.711812] usbcore: registered new device driver usb
[ 4.715667] zram: Added device: zram0
[ 4.740571] exFAT: Version 1.2.9
[ 4.753198] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.753201] ehci monitor start running
[ 4.753203] Mstar_ehc_init version:20180309
[ 4.753318] Sstar-ehci-2 H.W init
[ 4.753337] Get power-enable-pad from DTS GPIO(47)
[ 4.753365] [Enable_USB_VBUS] Enable USB VBUS GPIO(47)
[ 4.753369] Titania3_series_start_ehc start
[ 4.753373] [USB] config miu select [70] [e8] [ef] [ef]
[ 4.753375] [USB] enable miu lower bound address subtraction
[ 4.753378] [USB] init squelch level 0x2
[ 4.754394] [USB] no platform_data, device tree coming
[ 4.754405] [USB][EHC] dma coherent_mask 0xffffffffffffffff mask 0xffffffffffffffff
[ 4.754441] BC disable
[ 4.754449] [USB] soc:Sstar-ehci-2 irq --> 39
[ 4.754461] Sstar-ehci-2 soc:Sstar-ehci-2: EHCI Host Controller
[ 4.754501] Sstar-ehci-2 soc:Sstar-ehci-2: new USB bus registered, assigned bus number 1
[ 4.755631] Sstar-ehci-2 soc:Sstar-ehci-2: irq 39, io mem 0xfd285000
[ 4.790699] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.790706] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.790712] usb usb1: Product: EHCI Host Controller
[ 4.790717] usb usb1: Manufacturer: Linux 4.9.84 ehci_hcd
[ 4.790722] usb usb1: SerialNumber: mstar
[ 4.795393] hub 1-0:1.0: USB hub found
[ 4.795490] hub 1-0:1.0: 1 port detected
[ 4.796006] Sstar-ehci-1 H.W init
[ 4.796021] Titania3_series_start_ehc start
[ 4.796025] [USB] config miu select [70] [e8] [ef] [ef]
[ 4.796027] [USB] enable miu lower bound address subtraction
[ 4.796030] [USB] init squelch level 0x2
[ 4.797040] [USB] no platform_data, device tree coming
[ 4.797044] [USB][EHC] dma coherent_mask 0xffffffffffffffff mask 0xffffffffffffffff
[ 4.797071] BC disable
[ 4.797075] [USB] soc:Sstar-ehci-1 irq --> 38
[ 4.797081] Sstar-ehci-1 soc:Sstar-ehci-1: EHCI Host Controller
[ 4.797105] Sstar-ehci-1 soc:Sstar-ehci-1: new USB bus registered, assigned bus number 2
[ 4.842508] Sstar-ehci-1 soc:Sstar-ehci-1: irq 38, io mem 0xfd284800
[ 4.869745] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.869752] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.869757] usb usb2: Product: EHCI Host Controller
[ 4.869763] usb usb2: Manufacturer: Linux 4.9.84 ehci_hcd
[ 4.869767] usb usb2: SerialNumber: mstar
[ 4.877068] hub 2-0:1.0: USB hub found
[ 4.877160] hub 2-0:1.0: 1 port detected
[ 4.879529] [GOP]HalGopUpdateGwinParam 720: GOP_id=011 not support
[ 4.879534] [GOP]HalGopSetArgb1555Alpha 1208: GOPId=0x11 not support
[ 4.879537] [GOP]HalGopSetArgb1555Alpha 1208: GOPId=0x11 not support
[ 4.882097]
[ 4.882097] sstar_FB_SetBlending 402 u8GOP=1,u8win=0 aType=1 u8constAlpha=255
[ 4.882648]
[ 4.882649] SCSI subsystem initialized
[ 4.885363] libphy: Fixed MDIO Bus: probed
[ 4.902104] MSYS: DMEM request: [emac0_buff]:0x00000812
[ 4.919379] MSYS: DMEM request: [emac0_buff]:0x00000812 success, CPU phy:@0x26449000, virt:@0xC6449000
[ 4.923202] libphy: mdio: probed
[ 4.923213] mdio_bus mdio-bus@emac0: /soc/emac0/mdio-bus@emac0/ethernet-phy@0 has invalid PHY address
[ 4.923222] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 0
[ 4.947656] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 1
[ 4.947676] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 2
[ 4.947686] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 3
[ 4.947696] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 4
[ 4.947706] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 5
[ 4.947716] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 6
[ 4.947726] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 7
[ 4.947736] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 8
[ 4.947746] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 9
[ 4.947756] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 10
[ 4.947766] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 11
[ 4.947775] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 12
[ 4.947785] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 13
[ 4.947795] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 14
[ 4.947804] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 15
[ 4.947814] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 16
[ 4.947824] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 17
[ 4.947834] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 18
[ 4.947844] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 19
[ 4.947853] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 20
[ 4.947863] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 21
[ 4.947873] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 22
[ 4.947883] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 23
[ 4.947892] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 24
[ 4.947902] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 25
[ 4.947912] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 26
[ 4.947922] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 27
[ 4.947931] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 28
[ 4.947941] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 29
[ 4.947951] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 30
[ 4.947961] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 31
[ 4.948075] [emac_phy_connect][3216] connected mac emac0 to PHY at mdio-bus@emac0:00 [uid=11112222, driver]
[ 4.949039] MSYS: DMEM request: [emac1_buff]:0x00060812
[ 4.957175] MSYS: DMEM request: [emac1_buff]:0x00060812 success, CPU phy:@0x26450000, virt:@0xC6450000
[ 4.957908] libphy: mdio: probed
[ 4.957919] mdio_bus mdio-bus@emac1: /soc/emac1/mdio-bus@emac1/ethernet-phy@1 has invalid PHY address
[ 4.957927] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 0
[ 4.985992] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 1
[ 4.996025] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 2
[ 5.014700] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 3
[ 5.029172] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 4
[ 5.056049] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 5
[ 5.075492] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 6
[ 5.094322] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 7
[ 5.094564] ==20180309==> hub_port_init 1 #0
[ 5.094567] Plug in USB Port1
[ 5.121851] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 8
[ 5.135707] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 9
[ 5.151443] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 10
[ 5.162133] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 11
[ 5.170332] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 12
[ 5.178598] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 13
[ 5.187106] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 14
[ 5.195169] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 15
[ 5.203418] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 16
[ 5.212203] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 17
[ 5.220606] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 18
[ 5.229364] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 19
[ 5.237320] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 20
[ 5.245572] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 21
[ 5.254213] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 22
[ 5.262627] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 23
[ 5.271252] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 24
[ 5.274249] usb 2-1: new high-speed USB device number 2 using Sstar-ehci-1
[ 5.279704] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 25
[ 5.287701] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 26
[ 5.296464] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 27
[ 5.304833] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 28
[ 5.313531] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 29
[ 5.321896] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 30
[ 5.330631] mdio_bus mdio-bus@emac1: scan phy ethernet-phy at address 31
[ 5.339062] [emac_phy_connect][3216] connected mac emac1 to PHY at mdio-bus@emac1:00 [uid=00000000, driver]
[ 5.347357] usbcore: registered new interface driver usb-storage
[ 5.351082] >> [sdmmc] ms_sdmmc_probe
[ 5.353285] [Padmux]reset Pad_51(reg 0x101e08; mask0x300) to GPIO(org: SDIO_MODE_1)
[ 5.358594] >> [sdmmc_0] Probe Platform Devices
[ 5.374774] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 5.553939] usb 2-1: New USB device found, idVendor=1b20, idProduct=8888
[ 5.553947] usb 2-1: New USB device strings: Mfr=16, Product=32, SerialNumber=0
[ 5.553952] usb 2-1: Product: SigmaStarWIFI
[ 5.553958] usb 2-1: Manufacturer: SigmaStar inc
use rtc time[ 5.712523] client [813] connected, module:disp
[ 5.718531] [MI_SYSCFG_GetPanelInfo 50] eTiming = 4, hdmiTx = 1 Not Fund!!!
[ 5.726286] [MI_SYSCFG_GetPanelInfo 50] eTiming = 2, hdmiTx = 1 Not Fund!!!
[ 5.733826] [MI_SYSCFG_GetPanelInfo 50] eTiming = 8, hdmiTx = 1 Not Fund!!!
[ 5.740760] [MI_SYSCFG_GetPanelInfo 50] eTiming = 9, hdmiTx = 1 Not Fund!!!
[ 5.747776] [MI_SYSCFG_GetPanelInfo 50] eTiming = 10, hdmiTx = 1 Not Fund!!!
[ 5.755541] [MI_SYSCFG_GetPanelInfo 50] eTiming = 6, hdmiTx = 1 Not Fund!!!
[ 5.762589] [MI_SYSCFG_GetPanelInfo 50] eTiming = 7, hdmiTx = 1 Not Fund!!!
[ 5.769533] [MI_SYSCFG_GetPanelInfo 50] eTiming = 11, hdmiTx = 1 Not Fund!!!
[ 5.776639] [MI_SYSCFG_GetPanelInfo 50] eTiming = 13, hdmiTx = 1 Not Fund!!!
[ 5.783819] [MI_SYSCFG_GetPanelInfo 50] eTiming = 12, hdmiTx = 1 Not Fund!!!
[ 5.790960] [MI_SYSCFG_GetPanelInfo 50] eTiming = 14, hdmiTx = 1 Not Fund!!!
[ 5.798046] [MI_SYSCFG_GetPanelInfo 50] eTiming = 5, hdmiTx = 1 Not Fund!!!
[ 5.805160] [MI_SYSCFG_GetPanelInfo 50] eTiming = 3, hdmiTx = 1 Not Fund!!!
[ 5.812190] [MI_SYSCFG_GetPanelInfo 50] eTiming = 38, hdmiTx = 1 Not Fund!!!
[ 5.819312] [MI_SYSCFG_GetPanelInfo 50] eTiming = 50, hdmiTx = 1 Not Fund!!!
[ 5.826424] [MI_SYSCFG_GetPanelInfo 50] eTiming = 40, hdmiTx = 1 Not Fund!!!
[ 5.833705] [MI_SYSCFG_GetPanelInfo 50] eTiming = 43, hdmiTx = 1 Not Fund!!!
[ 5.840737] [MI_SYSCFG_GetPanelInfo 50] eTiming = 41, hdmiTx = 1 Not Fund!!!
[ 5.847834] [MI_SYSCFG_GetPanelInfo 50] eTiming = 44, hdmiTx = 1 Not Fund!!!
[ 5.855017] [MI_SYSCFG_GetPanelInfo 50] eTiming = 42, hdmiTx = 1 Not Fund!!!
[ 5.862160] [MI_SYSCFG_GetPanelInfo 50] eTiming = 46, hdmiTx = 1 Not Fund!!!
[ 5.869274] [MI_SYSCFG_GetPanelInfo 50] eTiming = 50, hdmiTx = 1 Not Fund!!!
[ 5.876384] [MI_SYSCFG_GetPanelInfo 50] eTiming = 45, hdmiTx = 1 Not Fund!!!
[ 5.883553] [MI_SYSCFG_GetPanelInfo 50] eTiming = 50, hdmiTx = 1 Not Fund!!!
[ 5.887974] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.897242] [MI_SYSCFG_GetPanelInfo 50] eTiming = 22, hdmiTx = 1 Not Fund!!!
[ 5.904386] [MI_SYSCFG_GetPanelInfo 50] eTiming = 23, hdmiTx = 1 Not Fund!!!
[ 5.911454] [MI_SYSCFG_GetPanelInfo 50] eTiming = 30, hdmiTx = 1 Not Fund!!!
[ 5.918655] [MI_SYSCFG_GetPanelInfo 50] eTiming = 32, hdmiTx = 1 Not Fund!!!
[ 5.926366] client [813] connected, module:panel
[ 6.316264] zram0: detected capacity change from 0 to 50331648
[ 6.370763] [Sstar_log]:Sstar_usb_module_init 0
[ 6.375138] [Sstar_log]:Sstar_init_firmware
[ 6.380028] [Sstar_log]:xxxx minstrel ht init
[ 6.384235] [Sstar_log]:SVN_VER=14606,DPLL_CLOCK=2,BUILD_TIME=[===USB-ARES_B==
[ 6.391889] [Sstar_log]:Probe called
[ 6.395315] [Sstar_log]:CONFIG_USE_DMA_ADDR_BUFFER TX_BUFFER_SIZE 800
[ 6.401860] [Sstar_log]:CONFIG_USB_AGGR_URB_TX enable cnt tx_dma_addr_buffer_end( (null))tx_dma_addr_buff0
[ 6.412771] [Sstar_log]:Sstar_usb_urb_malloc CONFIG_USE_DMA_ADDR_BUFFER max_num 4, total 131072
[ 6.421790] [Sstar_log]:CONFIG_USB_AGGR_URB_TX enable cnt tx_dma_addr_buffer_end(c64c0000)tx_dma_addr_buff8
[ 6.432558] [Sstar_log]:CONFIG_TX_NO_CONFIRM
[ 6.436782] [Sstar_log]:self->tx_hwChanId 0
[ 6.441029] [Sstar_log]:Allocated hw_priv @ c4ddd0a0
[ 6.445927] [Sstar_log]:Sstarwifi USB_USE_TASTLET_TXRX enable
[ 6.468478] [Sstar_log]:Sstar_before_load_firmware++
[ 6.473449] [Sstar_log]:+++++++++++++++++1.1v++++++++++++++++++
[ 6.479235] [Sstar_log]:===================~_~====================
[ 6.485993] [Sstar_log]:Sstar_start_load_firmware++
[ 6.490729] [Sstar_log]:Sstar_start_load_firmware: used firmware.h=
[ 6.497040] [Sstar_log]:Sstar_set_firmare:fw_iccm(c8c3c000)
[ 6.502767] [Sstar_log]:Sstar_set_firmare:fw_dccm(c8c5d000)
[ 6.508220] [Sstar_log]:Sstar_start_load_firmware: START DOWNLOAD ICCM=========
[ 6.515517] [Sstar_log]:Sstar_load_firmware_generic: addr 10000: len 20000
[ 6.526904] random: fast init done
[ 6.654418] [Sstar_log]:Sstar_start_load_firmware: START DOWNLOAD DCCM=========
[ 6.661597] [Sstar_log]:Sstar_load_firmware_generic: addr 800000: len 8000
[ 6.751640] [Sstar_log]:Sstar_after_load_firmware++
[ 6.757713] [Sstar_log]:Sstar_after_load_firmware:0x1610102c=0x4020e
[ 6.768692] [Sstar_log]:Sstar_after_load_firmware:0x1610102c=0x1020f
[ 6.775191] [Sstar_log]:Sstar_after_load_firmware:0x16101000=0x8000e08
[ 6.781977] [Sstar_log]:set_block_size=256
[ 6.784700] [Sstar_log]:firmwareCap f58f
[ 6.784704] [Sstar_log]:firmwareCap2 888f
[ 6.784721] [Sstar_log]:wsm_caps.firmwareCap 888ff58f
[ 6.784723] [Sstar_log]:apollo wifi WSM init done.
[ 6.784723] Input buffers: 32 x 2048 bytes
[ 6.784723] Hardware: 7.2
[ 6.784723] WSM firmware [=MODEM=RF=Ares_AX 2GHZ Dec 24 2019 19:59:25NOTXConfrim], ver: 8677, build: 2]
[ 6.784725] [Sstar_log]:EFUSE(8) [0]
[ 6.784727] [Sstar_log]:EFUSE(I) [0]
[ 6.784729] [Sstar_log]:EFUSE(B) [1]
[ 6.784731] [Sstar_log]:CAPABILITIES_SSTAR_PRIVATE_IE [1]
[ 6.784733] [Sstar_log]:CAPABILITIES_NVR_IPC [1]
[ 6.784735] [Sstar_log]:CAPABILITIES_NO_CONFIRM [1]
[ 6.784737] [Sstar_log]:CAPABILITIES_SDIO_PATCH [0]
[ 6.784740] [Sstar_log]:CAPABILITIES_NO_BACKOFF [0]
[ 6.784742] [Sstar_log]:CAPABILITIES_CFO [0]
[ 6.784744] [Sstar_log]:CAPABILITIES_AGC [1]
[ 6.784746] [Sstar_log]:CAPABILITIES_TXCAL [1]
[ 6.784748] [Sstar_log]:CAPABILITIES_MONITOR [0]
[ 6.784751] [Sstar_log]:CAPABILITIES_CUSTOM [1]
[ 6.784753] [Sstar_log]:CAPABILITIES_SMARTCONFIG [0]
[ 6.784755] [Sstar_log]:CAPABILITIES_ETF [1]
[ 6.784757] [Sstar_log]:CAPABILITIES_LMAC_RATECTL [1]
[ 6.784760] [Sstar_log]:CAPABILITIES_LMAC_TPC [1]
[ 6.784762] [Sstar_log]:CAPABILITIES_LMAC_TEMPC [1]
[ 6.784764] [Sstar_log]:CAPABILITIES_CTS_BUG [1]
[ 6.784766] [Sstar_log]:CAPABILITIES_USB_RECOVERY_BUG [1]
[ 6.784768] [Sstar_log]:CAPABILITIES_USE_IPC [1]
[ 6.784771] [Sstar_log]:CAPABILITIES_OUTER_PA [0]
[ 6.784773] [Sstar_log]:CAPABILITIES_POWER_CONSUMPTION [0]
[ 6.784775] [Sstar_log]:CAPABILITIES_RSSI_DECIDE_TXPOWER [0]
[ 6.784777] [Sstar_log]:CAPABILITIES_RTS_LONG_DURATION [1]
[ 6.784779] [Sstar_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[0]
[ 6.784781] [Sstar_log]:CAPABILITIES_SHARE_CRYSTAL [0]
[ 6.784784] [Sstar_log]:CAPABILITIES_HW_CHECKSUM [0]
[ 6.784786] [Sstar_log]:CAPABILITIES_SINGLE_CHANNEL_MULRX [1]
[ 6.784788] [Sstar_log]:CAPABILITIES_CFO_DCXO_CORRECTION [0]
[ 7.028272] [Sstar_log]:mdelay wait wsm_startup_done !!
[ 7.037283]
[ 7.037284] sstar_FB_SetBlending 402 u8GOP=1,u8win=0 aType=0 u8constAlpha=255
[ 7.047551]
[ 7.047552] [Sstar_log]:WSM_FIRMWARE_CHECK_ID
[ 7.054008] [ 7.055785] sstar_FB_SetBlending 402 u8GOP=1,u8win=0 aType=1 u8constAlpha=112
[ 7.063510] [ 7.165274] [Sstar_log]:wsm_generic_confirm:status(2)
[ 7.170200] [Sstar_log]:<WARNING> wsm_write_mib fail !!! mibId=4132
[ 7.176615] [Sstar_log]:apollo wifi : can't open /data/.mac.info
[ 7.182762] [Sstar_log]:efuse data is [0x1,0x3b,0x4,0x5,0x5,0xc,0x0,0x0,0x24:0x14:0x7:0x1:0xc6:0x46]
[ 7.192953] [Sstar_log]:apollo wifi : can't open /Sstar_txpwer_dcxo_cfg.txt
[ 7.200204] [Sstar_log]:ELOG_INIT len 64
[ 7.206728] [Sstar_log]:[Sstar_wtd]:set wtd_probe = 1
[ 7.212313] usbcore: registered new interface driver Sstar_wlan
[ 7.218091] [Sstar_log]:[wtd] register.
[ 8.074060] br-lan: port 1(eth0) entered blocking state
[ 8.081226] br-lan: port 1(eth0) entered disabled state
[ 8.086589] device eth0 entered promiscuous mode
[ 8.092606] br-lan: port 1(eth0) entered blocking state
[ 8.097691] br-lan: port 1(eth0) entered forwarding state
[ 8.449194] [Sstar_log]:br0_netdev_open()-1116: dev_get_by_name(br0) failed2![ 8.510565] [Sstar_log]:br!
[Sstar_log]:br0_netdev_open()-1116: dev_get_by_name(br0) failed2![ 9.168992] [Sstar_log]:br0_netdev_open()!
[ 50.329221] random: crng init done
